AERO
QTR_04.12
GO!
download Download This Article (PDF - 446 KB)
Understanding the New Widespread Fatigue Damage Rule
Understanding the New Widespread Fatigue Damage Rule

The development of widespread fatigue damage (WFD) in airplane structure is a concern for older airplanes. The U.S. Federal Aviation Administration (FAA) has published a rule that will limit the commercial usage of older airplanes, requiring service actions to preclude the onset of WFD and retirement.

By Amos W. Hoggard, Technical Fellow (Retired), Aging Airplane
Safety Rule/Widespread Fatigue Damage Program, and
Stephen R. Johnson, Aging Airplane Safety Rule/Widespread
Fatigue Damage Program Manager, Chief Structures Engineer

Operators will need to comply with the limits of validity specified in the airworthiness limitations as early as July 2013.

On Jan. 14, 2011, a new FAA rule (14 Code of Federal Regulations [CFR] 26 Subpart C) became effective requiring airplane manufacturers to make available service actions necessary to preclude the onset of WFD and to establish operational limits, known as limits of validity (LOV), of the maintenance program that effectively define an airplane’s usable life. It is important that operators become familiar with the rule so they can prepare for changes to airworthiness limitations that will limit how long an airplane may be operated in terms of flight cycles or flight hours.

This article describes Boeing’s approach to complying with the new rule and its impact on operators of Boeing airplanes throughout the world. It addresses the imminent future changes to airworthiness limitations, how those changes were developed, and how Boeing will assist operators with rule compliance.

About WFD

WFD in an airplane’s structure is defined as the simultaneous presence of cracks at multiple locations that are of sufficient size and density that the structure will no longer meet required damage tolerance and will not maintain required residual strength after partial structural failure (see fig. 1). The risk of WFD onset increases as airplanes are operated well past their original design objectives in flight cycles or flight hours.

Figure 1: Widespread fatigue damage (WFD)

The cracks on this lap splice are an example of WFD.

Figure 1

Fatigue Cracks

Because of the increased difficulty of identifying all of the necessary service actions and the inability of non-destructive inspections to reliably detect small cracks associated with the development of a WFD condition, airplane manufacturers, operators, and regulatory authorities have worked together to address WFD in aging airplanes. The result was the creation of the LOV concept that effectively establishes the life limit on an airplane based on when the existing fatigue test evidence is no longer sufficient to reliably predict structural behavior (see “Sources of fatigue test evidence” below).

Defining LOV
Sources of fatigue test evidence

The establishment of the LOV is based on the fatigue test evidence held by the manufacturer. Sources of this information include:

  1. Full-scale fatigue test.
  2. Full-scale component tests.
  3. Teardown and refurbishment of a high-time airplane.
  4. Less than full-scale component tests.
  5. Statistical fleet-proven life techniques.
  6. Evaluation of in-service problems/test data experienced by this model or other airplanes with similar design concepts.
  7. Analysis methods that have been parametrically developed to reflect fatigue test and service experience.

The LOV represents an operational limit based on fatigue test evidence that supports the maintenance program. The FAA defines the LOV as “the period of time (in flight cycles, flight hours, or both) up to which it has been demonstrated by test evidence, analysis and, if available, service experience and teardown inspections, that widespread fatigue damage will not occur in the airplane structure.” It is further defined as the point in the structural life of an airplane at which there is significantly increased risk of uncertainties in structural performance and probable development of WFD.

Once the airworthiness limitations containing the LOV are approved by the FAA, an airplane may not operate beyond the LOV.

Actions required of airplane manufacturers and operators

The FAA’s WFD rule specifies actions that are required of airplane manufacturers and operators.

Manufacturers must:

Operators must:

The FAA rule requires the manufacturer and the operator to comply by certain dates depending on the requirement in effect concerning damage tolerance (14 CFR 25.571) when the airplane was originally certified (see fig. 2).

Figure 2: Boeing compliance schedule

Boeing will provide amended airworthiness limitations containing limits of validity (LOV) to the FAA for each airplane model by the dates shown on this compliance schedule.

Group 1 Airplanes The first group of airplanes affected are those certified prior to 14 CFR 25 Amendment 45.

Figure 2a

Group 2 Airplanes The second group of airplanes affected are those certified between 14 CFR 25 Amendment 45 and 95.

Figure 2b

Group 3 Airplanes The third group includes all airplanes certified to 14 CFR 25 Amendment 96 or greater.

Figure 2c
Service bulletin actions to preclude the onset of WFD up to the LOV

As part of rule compliance, Boeing is required to identify WFD-susceptible areas for both the as-delivered structure and any structure that required modification by an airworthiness directive (AD). Boeing also must predict which of the identified WFD-susceptible areas will develop WFD prior to when the LOV is reached and provide service bulletin actions to prevent that development (see fig. 3). These service actions would be in the form of service bulletins that would require inspection, modification, or both. The FAA will issue an AD to make these service bulletins mandatory.

Figure 3: Example of structure susceptible to WFD

This skin splice at an aft pressure bulkhead is one area of airplane structure determined by the FAA to be susceptible to WFD.

Figure 3

To assist the industry in defining areas that might be susceptible to WFD, the FAA, with the assistance of operators and airplane manufacturers, identified 16 generic structural areas susceptible to developing WFD (see “Identifying WFD-susceptible structure” below). All of these areas are explained in the FAA Advisory Circular 120-104. This list is not meant to be inclusive of all structure that might be susceptible on any given airplane model, and it should only be used for general guidance.

Identifying WFD-susceptible structure

The FAA with operators and manufacturers documented 16 examples of airplane structure susceptible to multiple-site damage (MSD) and/or multiple-element damage (MED).

  • Longitudinal Skin Joints, Frames, and Tear Straps (MSD/MED)
  • Circumferential Joints and Stringers (MSD/MED)
  • Lap Joints with Milled, Chem-milled, or Bonded Radius (MSD)
  • Fuselage Frames (MED)
  • Stringer to Frame Attachments (MED)
  • Shear Clip End Fasteners on Shear Tied Fuselage Frames (MSD/MED)
  • Aft Pressure Dome Outer Ring and Dome Web Splices (MSD/MED)
  • Skin Splice at Aft Pressure Bulkhead (MSD) (see fig. 3)
  • Abrupt Changes in Web or Skin Thickness — Pressurized or Unpressurized Structure (MSD/MED)
  • Window Surround Structure (MSD/MED)
  • Over-Wing Fuselage Attachments (MED)
  • Latches and Hinges of Non-plug Doors (MSD/MED)
  • Skin at Runout of Large Doubler (MSD) — Fuselage, Wing, or Empennage
  • Wing or Empennage Chordwise Splices (MSD/MED)
  • Rib-to-Skin Attachments (MSD/MED)
  • Typical Wing and Empennage Construction (MSD/MED)

This list is not meant to be inclusive of all structure that might be susceptible on any given airplane model, and it should only be used for general guidance. It should not be used to exclude any particular structure.

Cost-benefit of specific service actions

While the establishment of the LOV will mandate the retirement of very old airplanes, the service bulletin actions to prevent WFD may present even more significant costs to the airline. Service bulletin actions include inspection, modification, or both and must be accomplished prior to utilization thresholds specified in the associated AD.

Similar to the requirements of LOV, operators may not operate airplanes that are past AD thresholds without complying with the AD-mandated inspection and modification requirements. The service bulletin actions for Boeing airplanes were developed with the assistance of the Structures Task Group (STG), which consists of Boeing, operators, and the FAA. The STG was asked to evaluate each proposed service bulletin action and ensure it was of value to the industry.

Using this information, Boeing has committed to make service bulletin actions available to the industry to enable operation up to the LOV (see fig. 4). Specific information about each of these bulletins may be found in the Aging Airplane Program Web site on the MyBoeingFleet.com products page under Structures Task Group.

Figure 4: Group 1 service bulletins required to preclude WFD

This table details the number of service bulletin actions for Group 1 airplanes (certified prior to 14 CFR 25 Amendment 45) that operators will be required to adopt in order to achieve the LOV.

Model Number of Inspection Bulletins Number of Modification Bulletins Number of Inspection and Modification Bulletins
727 2 0 0
737 5 3 2
747 5 3 7
DC-8 1 2 0
DC-9 2 1 0
DC-10 1 0 1
MD-80 1 0 0

A similar approach will be used to develop the compliance data for Group 2 and Group 3 airplanes.

Addressing WFD as an operator

Boeing will provide the FAA with updated airworthiness limitations containing the LOV for each airplane model in accordance with the compliance dates in figure 2. Following approval of the airworthiness limitations by the FAA, Boeing will make them available to operators on MyBoeingFleet.com. Operators will need to acquire the documents (per 14 CFR 91.403) and update their maintenance programs and have those programs approved by their FAA principal maintenance inspector by the dates specified in 14 CFR 121.1115 or 129.115 (see fig. 2).

For example, Boeing provided the compliance documents to the FAA on July 13, 2012, for the 727, 737-100/-200/-300/-400/-500, 747-100/-200/-300, DC-8, DC-9, DC-10, and MD-80. Subsequently, the FAA approved LOV values for Boeing’s Group 1 airplanes (see fig. 5). Updates to the airworthiness limitations are now available on MyBoeingFleet.com. Operators of Group 1 airplane models have until July 14, 2013, to integrate the LOV into their maintenance programs and develop a plan to stop operation of these airplanes when they reach the LOV. Boeing has also developed anticipated LOVs for the Group 2 and Group 3 airplanes (see fig. 6).

Figure 5: LOV for Group 1 Boeing airplane models

Model Minor Model LOV Airworthiness Limitation/Certification Maintenance Requirement (AWL/CMR) Document
Cycles Flight Hours
727 -100 Line No. 1–47 50,000 50,000 D6-8766-AWL
727 -100/-200 Line No. 48 + 85,000 95,000 D6-8766-AWL
737 -100/-200/-200 Cargo Line No. 1–291 34,000 34,000 D6-38278-CMR
737 -200/-200 Cargo/-300/-400/-500
Line No. 292–2565
75,000 100,000 D6-38278-CMR
737 -300/-400/-500 Line No. 2566–3132 85,000 100,000 D6-38278-CMR
747 -100, -200, -300, Special Performance 35,000 135,000 D6-13747-CMR
747 Short Range 35,000 135,000 D6-13747-CMR
747 -400 (Passenger and Freighter) 35,000 165,000 D621U400-9
747 -400 Domestic 35,000 165,000 D621U400-9
DC-8 All 56,000 125,000 MDC 12K9006
DC-9 All 110,000 110,000 MDC 12K9007
MD-80 All 110,000 150,000 MDC 12K9008
DC-10 All 60,000 160,000 MDC 12K1003

Figure 6: Anticipated LOV for Group 2 and Group 3 Boeing airplane models

These anticipated values are based on preliminary engineering calculations and are subject to final revision before final submission to the FAA. These LOV values are substantially beyond the original design service objectives embodied in the design of the airplanes. These are anticipated values only and are subject to revision. This information was part of Boeing multi-operator message 10-0783-01B, dated Dec. 19, 2010.

Model Minor Model Anticipated LOV
Cycles Flight Hours
Next-Generation 737 -600/-700/-700 Cargo/-800/-900/
-900 Extended Range
100,000 125,000
757 All 75,000 150,000
767 -200/-300 75,000 150,000
767 -300 Freighter/-400 Extended Range 60,000 150,000
777 -200/-200 Long Range/-300/
-300 Extended Range
60,000 160,000
777 Freighter 37,500 160,000
747 747-8 Intercontinental/747-8 Freighter 35,000 165,000
787 All 66,000 200,000
MD-10 All 60,000 160,000
MD-11 All 40,000 150,000
MD-90 All 110,000 150,000
717 All 110,000 110,000

In the near future, Boeing will begin publishing the service bulletin actions required to preclude WFD for Group 1 airplanes. These Boeing service bulletins will be identified by a statement in the background section of the bulletin. The FAA will mandate each of these bulletins in due course. If an airplane is above a specific threshold in the bulletin, Boeing recommends performing the service bulletin actions as instructed.

Boeing support of airplanes beyond LOV

Boeing estimates that approximately 25 Group 1 airplanes will exceed their FAA-approved LOV by the initial operational compliance date of July 14, 2013. Because the existence of WFD in the structure cannot be reliably detected by maintenance inspections beyond the LOV, Boeing strongly recommends that airplanes above their LOV be immediately and permanently removed from service. However, Boeing will continue existing support policies for these airplanes up to the date when operators are required to comply with the operational rule.

With the exception of certain military derivatives, including commercially certified airplanes in military service, Boeing will not provide support to airplanes beyond LOV after the date when operational compliance is required. This includes operations within the United States under any operational rules (not limited to Federal Aviation Regulations Parts 121 and 129), as well as airplanes operated outside of FAA jurisdiction. This also includes the 707/720 model, which has an FAA-defined LOV.

This policy will go into effect as of the respective operational rule compliance dates specified in 14 CFR 121.1115 or 129.115.

Resources for operators

Boeing has several means to keep operators informed of the latest information concerning WFD rule compliance. When significant information becomes available, Boeing will publish a multi-operator message or a service letter. Boeing also has recently introduced an Aging Airplane Program Web site on the MyBoeingFleet.com products page. This Web site is updated on a regular basis and contains links to the current versions of all service letters and multi-operator messages, as well as FAA rules and advisory circulars. It also provides directions for obtaining documents required for operator compliance.

Information concerning upcoming STG meetings and Boeing seminars on topics of general interest is also available on the Web site.

Summary

Concern about WFD increases as airplanes operate beyond their original design objectives. Manufacturers, operators, and the FAA have worked together to address WFD by defining service bulletin actions necessary to preclude the onset of WFD up to the LOV specified in the airworthiness limitations. Operators will need to comply with the LOV specified in the airworthiness limitations as early as July 2013 and to comply with future ADs.

For more information, please contact agingairplaneprograms@boeing.com.

Back to top | Continue to next article